Infineon's TLD5098 is an LED boost controller with built-in protection features that can adjust constant LED current to ensure LED color accuracy and long life. The device has multiple configurations such as boost, buck, drop-boost, SPEIC and flyback, etc. Input voltage from 4.5V to 45V, switching frequency from 100 kHz to 500 kHz, with a variety of protection features, mainly used in automotive interior and exterior lighting. This article describes the TLD5098 main features, block diagram, a variety of configurations List of application circuits and corresponding materials, as well as main features, circuit diagrams, and bill of materials for the LITIXTM Power TLD5098EL application board.
The TLD5098EL is a LED boost controller with built in protecTIon features. The constant current regulaTIon is often beneficial for LED color accuracy and longer lifetime.
The controller concept of the TLD5098EL allows multiple configurations such as Boost, Buck, Buck-Boost, SEPIC andFlyback by must adjusting the external components. The TLD5098EL offers the most flexible dimming options. Dimmingcan be achieved with analog or PWM input.The switching frequency is The TLD5098EL features an enable function reducing the shut-down current consumption to Iq_OFF< 10 μA. The current mode regulation scheme of this device provides a stable regulation loop maintained in the range of 100 kHz to 500 kHz and can be synchronized to an external clock source. This integrated soft start feature limits the current peak aswell as voltage overshoot at start-up. This IC is suited for use in the harsh automotive environments and provides output overvoltage protection, device overtemperature shutdown and short circuit to GND protection.
• Wide Input Voltage Range from 4.5 V to 45 V
• Constant Current or Constant Voltage Regulation
• Drives LEDs in Boost, Buck, Buck-Boost, SEPIC and FlybackTopology
• Very Low Shutdown Current: Iq_OFF< 10 μA
• Flexible Switching Frequency Range, 100 kHz to 500 kHz
• Synchronization with external clock source
• PWM Dimming
• Analog Dimming feature to adjust average LED current
• Internal 5 V Low Drop Out Voltage Regulator
• Open Circuit Detection
• Short to GND Protection
• Output Overvoltage Protection
• Internal Soft Start
• Over Temperature Shutdown
• Wide LED current range via simple adaptation of external components
• 300mV High Side Current Sense to ensure highest flexibility and LED current accuracy
• Available in a small enhanced PG-SSOP-14 package
• Automotive AEC Qualified
• Green Product (RoHS) Compliant
• Automotive Exterior and Interior Lighting
Figure 1. TLD5098 block diagram
Figure 2. TLD5098 Application Circuit Diagram: B2G Configuration Figure 2 Application Circuit Material List:
Figure 3. TLD5098 SEPIC Application Circuit Diagram: Buck-Boost Configuration Figure 3. Material List of TLD5098 SEPIC Application Circuits:
Figure 4. TLD5098 Flyback Application Circuit Diagram: Buck-Boost Configuration Figure 4. TLD5098 Flyback Application Circuit Material List:
Figure 5. TLD5098 Boost-Battery Application Circuit Diagram: B2B (Buck-Boost Configuration)
Figure 5 TLD5098 Boost-Battery Application Circuit Material List:
Figure 6. TLD5098 Buck Application Circuit Diagram Figure 6 TLD5098 Buck Application Circuit List of Materials:
Figure 7. TLD5098 boost application circuit diagram Figure 7 TLD5098 boost application circuit material list:
LITIXTM Power TLD5098EL Application Board
The size of the application boards is 4.5 cm x 4 cm and the connections to the power supply and external load can be established with cables.
The application boards in combination with real loads enable fast and realistic application prototyping and could be very beneficial for constructing initial system demonstrators.
The layout of these boards is optimized for EMC and can be reused for customer applications.
Figure 8. LITIXTM Power TLD5098EL Application Board Outline Drawing: B2G Configuration
Figure 9. LITIXTM Power TLD5098EL Application Board Schematic: B2G Configuration
LITIXTM Power TLD5098EL Application Board Material List: B2G Configuration
General materials of hot dip galvanized Screw Bolt nut is Q235 ,35K ,45# ,35CrMo,etc.According to the engineering requirements, the corresponding different grades Screw bolt nut are selected respectively .Generally ,the high-grade Nut products such as 35K,45# C35CrMo are prreferred for UHV lines, Mainly include :
1) High strength Nut
2)35 Crmo Nut
3) Thinckening of Nut
4) Enlarged bore Nut
5) Fine buckle Nut
6)Slotted Nut
7)Flange Nut
8) Lock Nut
According to strength grades ,there are 4,6,8,8.8,10.9grade ,for construction of differeent fields ,can use hot dip galvanized Flange nut ,Helix nut ,or other nuts .
Flange Nut,Carbon Steel Nut,Lock Nut,Stainless Steel Nut,Helix Nut
BAODING JIMAOTONG IMPORT AND EXPORT CO., LTD , https://www.chinagroundscrew.com