A lot of TVs now support WiFi connection, but we should all have a problem: The TV is not connected to WiFi. In fact, there are many reasons why the TV is not connected to WiFi, but we will ignore it and think that it is our own TV problem. Today, Xiao Bian gave everyone a talk about how Skyworth TV did not connect to WiFi.
Method one: Turn off and restart the TV When the WiFi connection fails to access the Internet, Xiao Bian first recommends turning off the TV, turning off the power, placing it for 30 seconds, and then connecting the power supply and restarting the TV. Restarting the TV can reset the system so that the system can recognize the WiFi signal again.
Method two: Turn off and restart the TV WiFi connection
If you have set up a WiFi connection on your TV, a network IP address assigned by another WiFi connection has been reserved on the TV. It will be applied to the current WiFi. If the address patterns are the same and there are no address conflicts, there is nothing to worry about. But occasionally the system should make mistakes in data. Therefore, the user needs to follow the steps below to shut down and restart the WiFi connection:
1. Click to open the menu.
2, enter the setting bar.
3. Select the Wireless and Network Settings section.
4, enter the WiFi setup project.
5. Select Close WiFi in a new window.
6. After completing the close operation, re-enter the project and select Open WiFi.
Method 3: If the above method does not work, you need to choose to ignore the network in the TV WiFi settings and re-add it.
1. Find the connected network in the TV WiFi settings.
2, choose to ignore the network.
3, waiting for the network to automatically display.
4. Select and enter the network password to log in to the network.
Method 4: Verify that the router's signal is normal and the weak signal is too weak. It may not be able to connect to WiFi. If yes, Xiao Bian has the following solutions:
1, the first position
Many people will put the router behind a hidden corner or TV cabinet. After testing, to enhance the home WiFi signal, it is best to place the router in a place that is not obstructed by a wall or home. If it is a duplex or a three-room, two-bedroom apartment, it is best to place the router in the center of the house so that the WiFi signal can be fully covered.
2, reduce interference equipment
Mobile phones, microwave ovens, appliances with WiFi modules, or even neighboring routers will interfere with WiFi signals. If you do not want to re-purchase the dual-band router to solve the problem, it is best to move the wireless router around the jammer.
3, do it yourself to expand the coverage
The most popular DIY method is to use cans to enhance the signal. The method is simple: Cut the bottom of the can, cut the entire bottom, and then open the can to open the router antenna through the can. If there are old routers that are eliminated in the home, set the old router to AP mode according to the instructions, and then connect to the home router currently used in the home through the LAN port, you can also expand the home WiFi signal.
4, antenna placement angle
The omni-directional antennas on most wireless routers are "ring-shaped" stereoscopic coverage. In the vertical direction, WiFi signal coverage is wider. It is worth noting that when the antenna of the router is placed in the vertical direction, the signal coverage weakness is above and below. In practical use, a suitable angle can be selected according to the use distance and height.
5, find the correct wireless channel
Now basically every household has a wireless router installed, and these routers will interfere with each other, resulting in poor signal quality. Wireless routers can choose to work on different channels, but use a scanning tool like WiFi Stumbler or WiFi Alyzer to find the best channel in the house.
6, timing restart
Sometimes overheating, aging, and excessive downloading of the router cause signal coverage to be reduced. Therefore, consider setting the router to restart automatically every day. A lot of firmware or timing software has this function, after restarting the router, WiFi can become faster and more stable.
7, release the potential of the router
After the wireless router is installed, turn on the power, enter the security settings, adjust the router speed to maximum, and set the router to use only one 802.11 protocol. Many routers are factory-set to operate at a rate of 75%, and many routers are set to hybrid mode. After adjusting to a single protocol, the rate can be significantly increased.
8, additional optional power cat
If the home space is too large or there are many floors, the WiFi signal is difficult to cover. The cat can be used to adjust the network signal to the wire and use the existing wires to solve the network transmission. The power cat is connected to the router through the network cable, and then the power is turned on. The power line carrier communication is realized under the same power meter. Happy and wireless Internet access in other rooms, plug in a wireless power cat on it.
9, buy multi-antenna router
If your home wireless router has been used for a long time, replacing a new two-antenna, multi-antenna router is not a good option. One of the signal transmission technologies is newer and newer routers can bring more efficient propagation and less loss.
Method 5: Restart the modem and router
Modems and routers are usually in a long working state. Individual families using a WiFi network will not turn off the routers or modems. The system will inevitably cause data errors during long-time operation. Therefore, if WiFi cannot be connected, you can try to restart the router. Demodulator or router. Normally, the modems and routers do not have hard switches. The user only needs to turn off the power for 30 seconds and restore power. Remember! ! Do not reset the router! Otherwise the router data will be cleared and need to be reset.
Method 6: Check if the router is stationary Skyworth TV's network card address. We can go into the router system settings, turn off access bans, or add Skyworth TVs to allow connected devices.
Method 7: Check whether the gateway and DNS in the wireless network are normal. It is recommended that Skyworth TV wifi be set to be automatically obtained. If you use manual acquisition, whether to fill in the IP address is correct. Check if the DNS is correct.
Method 8: If it is not feasible, Skyworth TV grayscale factory settings
1. Decrease the volume to “00â€, press and hold down the “Volume minus†button on the panel, and press the “On-Screen Display†button of the remote control at the same time to enter the factory debugging mode.
2. In the factory debugging mode, press the number key “6†on the remote control. The “P-MOD†menu (requires password input) will be displayed on the screen. Press the number keys “7â€, “8â€, and “9†in order. ".
3. Press the “Menu†key four times in succession to call up the “PE-2†menu. Move the status bar (cursor) to the “INIT†item and press the “Volume Plus†button to make the “INIT†item data from “00â€. †becomes “FFâ€. If the parameter of the "INIT" item cannot be changed to "FF", or it is still an English menu or cannot be received after changing to "FF", it is necessary to check whether the seventh pin of the EEPROM is low level during initialization.
4, press the AC power switch off, and then restart, that is, complete the initialization operation.
Method one: Turn off and restart the TV When the WiFi connection fails to access the Internet, Xiao Bian first recommends turning off the TV, turning off the power, placing it for 30 seconds, and then connecting the power supply and restarting the TV. Restarting the TV can reset the system so that the system can recognize the WiFi signal again.
Method two: Turn off and restart the TV WiFi connection
If you have set up a WiFi connection on your TV, a network IP address assigned by another WiFi connection has been reserved on the TV. It will be applied to the current WiFi. If the address patterns are the same and there are no address conflicts, there is nothing to worry about. But occasionally the system should make mistakes in data. Therefore, the user needs to follow the steps below to shut down and restart the WiFi connection:
1. Click to open the menu.
2, enter the setting bar.
3. Select the Wireless and Network Settings section.
4, enter the WiFi setup project.
5. Select Close WiFi in a new window.
6. After completing the close operation, re-enter the project and select Open WiFi.
Method 3: If the above method does not work, you need to choose to ignore the network in the TV WiFi settings and re-add it.
1. Find the connected network in the TV WiFi settings.
2, choose to ignore the network.
3, waiting for the network to automatically display.
4. Select and enter the network password to log in to the network.
Method 4: Verify that the router's signal is normal and the weak signal is too weak. It may not be able to connect to WiFi. If yes, Xiao Bian has the following solutions:
1, the first position
Many people will put the router behind a hidden corner or TV cabinet. After testing, to enhance the home WiFi signal, it is best to place the router in a place that is not obstructed by a wall or home. If it is a duplex or a three-room, two-bedroom apartment, it is best to place the router in the center of the house so that the WiFi signal can be fully covered.
2, reduce interference equipment
Mobile phones, microwave ovens, appliances with WiFi modules, or even neighboring routers will interfere with WiFi signals. If you do not want to re-purchase the dual-band router to solve the problem, it is best to move the wireless router around the jammer.
3, do it yourself to expand the coverage
The most popular DIY method is to use cans to enhance the signal. The method is simple: Cut the bottom of the can, cut the entire bottom, and then open the can to open the router antenna through the can. If there are old routers that are eliminated in the home, set the old router to AP mode according to the instructions, and then connect to the home router currently used in the home through the LAN port, you can also expand the home WiFi signal.
4, antenna placement angle
The omni-directional antennas on most wireless routers are "ring-shaped" stereoscopic coverage. In the vertical direction, WiFi signal coverage is wider. It is worth noting that when the antenna of the router is placed in the vertical direction, the signal coverage weakness is above and below. In practical use, a suitable angle can be selected according to the use distance and height.
5, find the correct wireless channel
Now basically every household has a wireless router installed, and these routers will interfere with each other, resulting in poor signal quality. Wireless routers can choose to work on different channels, but use a scanning tool like WiFi Stumbler or WiFi Alyzer to find the best channel in the house.
6, timing restart
Sometimes overheating, aging, and excessive downloading of the router cause signal coverage to be reduced. Therefore, consider setting the router to restart automatically every day. A lot of firmware or timing software has this function, after restarting the router, WiFi can become faster and more stable.
7, release the potential of the router
After the wireless router is installed, turn on the power, enter the security settings, adjust the router speed to maximum, and set the router to use only one 802.11 protocol. Many routers are factory-set to operate at a rate of 75%, and many routers are set to hybrid mode. After adjusting to a single protocol, the rate can be significantly increased.
8, additional optional power cat
If the home space is too large or there are many floors, the WiFi signal is difficult to cover. The cat can be used to adjust the network signal to the wire and use the existing wires to solve the network transmission. The power cat is connected to the router through the network cable, and then the power is turned on. The power line carrier communication is realized under the same power meter. Happy and wireless Internet access in other rooms, plug in a wireless power cat on it.
9, buy multi-antenna router
If your home wireless router has been used for a long time, replacing a new two-antenna, multi-antenna router is not a good option. One of the signal transmission technologies is newer and newer routers can bring more efficient propagation and less loss.
Method 5: Restart the modem and router
Modems and routers are usually in a long working state. Individual families using a WiFi network will not turn off the routers or modems. The system will inevitably cause data errors during long-time operation. Therefore, if WiFi cannot be connected, you can try to restart the router. Demodulator or router. Normally, the modems and routers do not have hard switches. The user only needs to turn off the power for 30 seconds and restore power. Remember! ! Do not reset the router! Otherwise the router data will be cleared and need to be reset.
Method 6: Check if the router is stationary Skyworth TV's network card address. We can go into the router system settings, turn off access bans, or add Skyworth TVs to allow connected devices.
Method 7: Check whether the gateway and DNS in the wireless network are normal. It is recommended that Skyworth TV wifi be set to be automatically obtained. If you use manual acquisition, whether to fill in the IP address is correct. Check if the DNS is correct.
Method 8: If it is not feasible, Skyworth TV grayscale factory settings
1. Decrease the volume to “00â€, press and hold down the “Volume minus†button on the panel, and press the “On-Screen Display†button of the remote control at the same time to enter the factory debugging mode.
2. In the factory debugging mode, press the number key “6†on the remote control. The “P-MOD†menu (requires password input) will be displayed on the screen. Press the number keys “7â€, “8â€, and “9†in order. ".
3. Press the “Menu†key four times in succession to call up the “PE-2†menu. Move the status bar (cursor) to the “INIT†item and press the “Volume Plus†button to make the “INIT†item data from “00â€. †becomes “FFâ€. If the parameter of the "INIT" item cannot be changed to "FF", or it is still an English menu or cannot be received after changing to "FF", it is necessary to check whether the seventh pin of the EEPROM is low level during initialization.
4, press the AC power switch off, and then restart, that is, complete the initialization operation.
medical transformer,adt transformers,lighting transformer,amp transformer
IHUA INDUSTRIES CO.,LTD. , https://www.ihua-sensor.com